PrimaLuna
EVO 100 Digital Analog Converter

PrimaLuna
EVO 100 Digital Analog Converter

$4,695

Introducing the world’s first tube-based data clocking device: the SuperTubeClock™

Local pickup or $11 flat rate shipping within Australia
Introducing the world’s first tube-based data clocking device: the SuperTubeClock™
By incorporating a low-noise mini-triode vacuum tube into the digital clock, this boldly conceived design provides vastly superior resolution, detail retrieval, improved clarity, increased definition and detail from top to bottom.
AC OFFSET KILLER

AC Offset Killer is about goose bumps. The ones you get when music comes out of a background so quiet, you may say to yourself “Just how is this possible?” PrimaLuna custom-winds our own massive toroidal power transformers that are low in hum and EMI. But we wanted more. Our engineers designed the AC Offset Killer to lower transformer noise to a place no other manufacturer dreams of going, regardless of how bad your electricity is. The result? Sense of space. Texture. The resonance of an acoustic guitar or violin string that seems to trail on forever. The AC Offset Killer will amaze you.

Premium PartsPremium parts including polypropylene coupling caps, triple pi power supply filters, custom designed isolation transformers which separate the analog and digital devices, resulting in decreased signal degradation and improved sonics from top to bottom. Many DACs weigh in at ten pounds or less. The EVO 100 Tube DAC weighs nearly 29 pounds!

Point To Point WiringYou spend a lot of money on interconnects. So why have the signal go right from the RCA jacks or speaker terminals into circuit boards with copper traces so thin you can hardly see them? What’s high-end about that?

PrimaLuna employs Point to Point Wiring on all products. The entire signal path, including resistors and capacitors, is painstakingly hand wired with heavy-gauge cable by craftsman.

Dual Mono Topology

Per channel dedicated tubes. While it is fine to use a single tube as a buffer for both channels and claim your DAC is “tube”, it can’t be compared to the PrimaLuna design and what it does for the music.

Vacuum Tube Rectified

Vacuum tube rectified power supply incorporates eleven separate power supply regulation circuits. Tube rectification is synonymous with organic sound, especially when compared to DACs being known as sounding like “a computer”.
USB Digital Input

USB digital input allows using your computer for storage and playback of your music with all the benefits of features like playlists and easier access to your whole music library. Rather than just add in an USB input as an afterthought, PrimaLuna engineers searched endlessly looking for the best-sounding USB interface we could find. Our USB input converts the jitter-filled USB digital signal to S/PDIF, dramatically improving the digital signal quality before it gets to the SuperTubeClock. This USB input is a true high-resolution digital input.

The SuperTubeClock™

This is where the magic happens… the SuperTubeClock™ replaces the solid state oscillator normally found in a DAC with a mini triode vacuum tube. By using a tube, we have significantly lowered the amount of jitter and noise, resulting in superior detail retrieval. This in turn yields superior detail and dynamics from top to bottom, and improved overall musicality.

First a note on the tube itself: The tube is a very rugged, long-life Russian military Triode specifically designed for oscillation purposes… which is its function here. It is running very conservatively so life expectancy is roughly 5 to 10 years of operating time. The small glass envelope guarantees very low microphonics.

Triode tubes are inherently low noise devices, and extremely linear when used properly. This means that the oscillation frequency wave it produces is very pure and clean. The noise in the sidebands, from 10Hz to 100kHz on either side of the oscillation frequency, is extremely low. This is the important spectrum for audio. Everything below and beyond that can be ignored.

When you reclock the inputs, any noise that is generated here appears unfiltered and unattenuated at the input of the conversion chip, and injects jitter, which from then on is an indistinguishable part of the digital audio stream. No amount of cleaning will ever be able to remove this noise once it reaches this point; it has become part of the audio signal. This noise “rides” on the audio signal, so you do not hear it as noise, but as smearing of notes and masking of detail. There is a distinctive loss of dynamics, tonal purity, inter-transient silence, and sense of timing. We call this “noise modulation.”

This is why the low noise, especially in the 10Hz-100kHz sidebands of the oscillator, is so crucial. Again: below and beyond these frequency extremes is trivial, because it will not affect the audio, and will not reach the analog outputs.

When the clock is used to clock the DAC chip, a similar situation occurs as described above: the noise appears at the location where the digital audio stream is converted to successive steps in a staircase wave, which represents the analog audio signal. Each step has to be EXACTLY 1/441000th, 1/96000th, 1/176400th, or 1/192000th. The injected noise introduces a deviation in time which is the exact replica of that noise. This means that the audio signal at the outputs of the DAC chip has the noise riding on it, again as an inherent part of the signal. No amount of filtering will remove the noise once it reaches this step. Again we experience that smear and detail masking, with that distinctive loss of dynamics, tonal purity, inter-transient silence, and sense of timing. Here you see how much sense it makes to reclock BOTH the inputs AND the DAC chip.

The oscillation frequency wave a tube produces is a sine wave. That’s no good: It has to be converted to a square wave. This is a very delicate procedure: when the rising and falling edges of a square wave are not steep enough, there exists a certain window during which the actual transition of the data bit is not exactly time-defined. It leaves room to be either too late or too early. This is a partly random process, and partly dependent on surrounding conditions; such as power supply voltage variations, ground noise, inherent CMOS or chip crosstalk in the decoder or DAC chip, etc. All these timing variations are noise, and are called jitter from various sources. The steeper the edges, the more exactly defined the transition moment will be, resulting in less noise (jitter). When a clock produces a very stable frequency with such low jitter, there will be a more accurate reproduction of the original analog waveform of the music.

Here are a few real SuperTubeClock™ pictures of what it can do: experts will certainly like them. No other commercial clock on earth will produce a square wave as this one.

Each square wave seen below is measured on a Philips PM3295A analog 400MHz oscilloscope using LeCroy 10:1 probes. These probes attenuate the signal by a factor of 10, in order to not load the device under test with any load, resistive or capacitive. So the vertical resolution on the scope image has to be multiplied by 10. For instance when you see ~0.1V, then it is in reality measuring ~1V(AC).

The SuperTubeClock™ generating a square wave at 8.4672mHz. The vertical slope is measured at ~500mV (each black horizontal line represents 500mV counting from top to bottom). The vertical peak-to-peak travel of the square wave at this frequency is 3.5 Volts, which is excellent.

Each black vertical line going from left to right represents 10 nanoseconds. The faster a clock can go from peak to peak, the better.

Square waves present themselves more and more like sine waves the higher you go in frequency. So an 8.4672mHz wave like the one above is still identifiable as a square wave, but as we approach 42.2mHz, typically a square wave will be almost fully rounded off and appear as a sine wave. As a square wave begins to round off, it means the timing of the digital transmissions has become more insecure, allowing for the introduction of more noise and jitter that is then presented to the DAC.

Here we see the square wave generated by the SuperTubeClock™ at 42.2mHz. As you can see, the square wave still has a very discernible square shape. This means the clock is VERY fast, leaving very little time to introduce jitter and noise which can interfere with sound quality as mentioned above. Look closely at the image on the left (click to enlarge). Each black vertical line running from left to right represents 5 nanoseconds. The time it takes the slope to go from the top bar to the bottom takes up roughly 1/3 of that black square, which is about 1.67 nanoseconds.

Think about it.. that’s 1.6 BILLIONTHS of a second. Each black horizontal line in this measurement represent ~1V from top to bottom. Just as in the first wave above, the peak-to-peak travel at 42.2mHz is about 3.6 Volts, which again is excellent.

This kind of speed is crucial to ensure accuracy in detail retrieval. This in turn introduces less noise and jitter, resulting in better transients, increased clarity, improved dynamics, and a pure, musical tonality.

Weight 13 kg
Dimensions 280 × 403 × 190 mm
Brand

Inputs

PCM support

DAC Chipset

Tube Complement

2 – 12AX7
2 – 12AU7
2 – 5AR4

Color

Black, Silver

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.

At Len Wallis Audio, whether you’re purchasing in store, over the phone or online through our ecommerce store, we want you to be completely satisfied with your purchase.

Our Refund, Return and Repairs Policy is here to clarify any concerns or questions you might have prior to you making a purchase from us. This way you can be sure of our policy on refunds, returns and repairs and your rights under the Australian Consumer Law.

We also recommend you immediately inspect any goods that you receive from us to ensure you are completely satisfied with the goods, including that the goods are of acceptable quality, and match the description we have provided to you.

If you have any questions about this policy, please contact us at sales@lenwalluisaudio.com.au or 02 9427 6755

We require a receipt or proof of purchase.

  • Please do not send your purchase back to the original manufacturer.
  • There are certain situations where only partial refunds are granted (if applicable). For example:
    • Any item not in its original condition, is damaged or missing parts for reasons not due to our error
    • Any item that is returned for reason of change of mind more than 14 days after delivery or purchase from the store.

Consumer Guarantees and Your Rights under the Australian Consumer Law

Refer to our page for more information.

Goods Damaged in Transit.

If any goods arrive damaged, please contact us as soon as possible. Len Wallis Audio will arrange to have the damaged goods returned and either arrange for a replacement of the goods or refund the price to you. Damaged goods must be returned in the condition received by you with all original packaging, accessories and/or manuals.

Refunds

Refunds will be normally be processed within five (5) days.

Delivery Charges

Where Len Wallis Audio considers the goods to have breached a consumer guarantee, any shipping costs to return the goods to Len Wallis Audio will be at our cost.

Returns and Repairs.

You may visit Len Wallis Audio and a staff member will assist you with any return or repair. This may include inspecting the goods, arranging for the goods to be repaired, or providing you with a replacement.

Goods must be returned within a reasonable time. 

If any goods cannot be easily returned to us due to their size, the fault or because they have been affixed or installed in your premises, please contact us and we will arrange an inspection to assess the goods.

Goods returned for repair will be assessed and/or repaired within a reasonable time. You may be provided with an indicative repair time, which time may vary due to reasons beyond ours or the repairer’s reasonable control, such as part availability and incorrect fault description.

You may be required to pay labour, assessment and/or freight fees, such as where goods are assessed to have been damaged by misuse or accident, or where your rights under the Australian Consumer Law or any manufacturer’s warranty do not apply. We may provide you with an indicative fee, which may vary due to reasons beyond our control.

If any goods that you return are capable of retaining user generated data such as files stored on a hard drive, and songs stored on a portable media player, the replacement or repair of the goods may result in loss of the data. In these circumstances, we recommend you back up data to prevent data loss, and remove sensitive or confidential data, as a party assessing and/or repairing your goods may be required to view data in the course of carrying out the assessment. We will not be responsible for any data loss.

In some circumstances, goods presented for repair may be replaced by refurbished goods of the same type rather than being repaired. Refurbished parts may be used to repair the goods.

Contact Us

Where you have any questions or concerns relating to your Order, please immediately contact us

We understand that sometimes you may simply change your mind about a purchase or have made a wrong selection. In these situations, you have 14 days in which to return your item for a refund, exchange or store credit. If more than 14 days has passed since your purchase we can’t offer you a refund, exchange or store credit.

To be eligible for a return, refund or store credit your item must be in the same condition that you received it. Which is to say, it must be in the original unopened packaging, and in ‘brand new’ saleable condition.

Please note that current Australian Consumer Law does not require us to offer a ‘Change of Mind’ refund. Rather Len Wallis Audio offers 14 day ‘Change of Mind Policy’ in good faith. For more information on consumer rights and guarantees, please visit the Australian Competition and Consumer Commission web site.